Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
We have come across this great article pertaining to Installing A Bathtub below on the internet and decided it made perfect sense to write about it with you on my blog.
Setting up a tub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old tub with a new one is additionally a reasonably tough job. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly need an assistant to vacate the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. As opposed to working with a contractor to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might need a professional plumber to make tube links.
This post will aid you mount a new bath tub in your shower room if you have currently gotten a new bathtub as well as do not need to alter the arrangement of your previous supply of water pipelines.
Your tools as well as material list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be rather troublesome as a result of the limited access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, place the bath tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the bathtub till the level checks out level.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the water system and check all joints as well as new pipework for leakages as well as tighten them if required. Load the tub and additionally inspect the overflow outlet and also the typical electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet and the sink. Safeguard the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing complications with moisture and possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly load the bathtub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that editorial on Installing A Bathtub from a good friend on our other site. Are you aware of someone else who is excited about How to Install a Bathtub? Please feel free to share it. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Book Your Appointment Report this page